- #Cisco asa show license command software
- #Cisco asa show license command password
- #Cisco asa show license command license
Security Contextsīy default the ASA has 2 contexts that can be ran simultaneously.
#Cisco asa show license command license
EncryptionĮncryption-DES comes standard on all firewalls.Įncryption-3DES-AES is a $0 cost license that enables 3DES and AES encryption methods. If one firewall goes down, the remaining one becomes Active for both Contexts. This may be used when Primary firewall is the Active firewall for Context A, and the secondary fireall is the Active firewall for Context B. This failover usually occurs without dropping a packet because the connection table is actually replicated between the two units.Īn Active/Active scenario is generally used for multi context firewalls. So if the primary firewall goes down, the standby unit will kick over to active and even take over the active IP. The active firewall will keep the active IP. In an Active/Standby scenario, one firewall acts as the active one and accepts connections going through it. Failover is when two firewalls (which are matching models and hardware) are paired together for redundancy. This is not to be confused with “Clustering”. This specifically means the ASA will only build connections for 10 hosts within the network at a time. The 5505 comes with 10 hosts standard and can be upgraded to 50 or Unlimited number of hosts. This is “Unlimited” in all models except for the 5505. A sec plus license can be applied to remove this restriction. The DMZ interface is restricted to only be able to pass traffic to either the inside interface or outside but cannot pass traffic to both. Suppose these are “inside” and “outside”. Two VLANs can talk to each other without issues. The “DMZ Restricted” term indicates a further restriction. This is stating only 3 VLANs can be created which are then eligible to be applied to an interface. On the 5505 each interface is assigned a VLAN. On the Cisco ASA 5505 you may see a line stating: Now we will cover each of these items in detail. Intercompany Media Engine : Disabled perpetual
![cisco asa show license command cisco asa show license command](https://www.proprofs.com/quiz-school/topic_images/p18r3gqh0g1kpn18uvar34pk1fmc3.jpg)
It is applicable only when the module is in the Recover state.An圜onnect Essentials : Disabled perpetualĪn圜onnect for Mobile : Disabled perpetualĪn圜onnect for Cisco VPN Phone : Disabled perpetualĪdvanced Endpoint Assessment : Disabled perpetualīotnet Traffic Filter : Disabled perpetual Sw-module module ips recover stop -This command stops the reimage of the ASA 5500-X IPS SSP. It is applicable only when the module is in the Up state.
![cisco asa show license command cisco asa show license command](http://i.ytimg.com/vi/5ltNfaPz0nA/maxresdefault.jpg)
Sw-module module ips recover boot -This command reimages the ASA 5500-X IPS SSP. You must first copy the IPS image to the ASA to disk0:/. Sw-module module ips recover image disk0:/ image name -This command starts the reimage process by setting the image location and name.
#Cisco asa show license command password
Sw-module module ips password-reset- This command restores the cisco CLI account password on the ASA 5500-X IPS SSP to the default cisco. It is applicable when the module is in the Up/Down/Unresponsive/Recover states. Sw-module module ips reset -This command performs a hardware reset of the ASA 5500-X IPS SSP. It is effective only when the module is in Up state.
#Cisco asa show license command software
Sw-module module ips shutdown- This command shuts down the software on the ASA 5500-X IPS SSP. It is effective only when the module is in the Up state. Sw-module module ips reload- This command reloads the software on the ASA 5500-X IPS SSP without doing a hardware reset.